This year I will…

This year I will read more books and work on my projects more.

Back in May 2010 I blogged about the projects I wanted to complete last year. Well, suffice to say I didn’t achieve them all, but I did make some good progress on some, and none on others.

My ball mill is pretty much finished, it just needs some minor adjustments. The weather balloon project didn’t get much further, but I do have most of the equipment (excluding the actual camera yet), so hopefully this will happen around spring/summer time. The iPhone app project didn’t get anywhere, partly because Jay left the place I work, but also because I’m not that organised!

Although not mentioned in that blog post, one of my New Year’s Resolutions last year was to start tackling some of the bigger projects on my house. I don’t normally make any, so that year they were all practical things. That project was meant to be double glazing throughout, followed by a new kitchen/diner, followed by a new lounge this year. It actually turned out to be double glazing and a new lounge (after a small accident with some gloss paint and a carpet), so the kitchen will have to wait. The lounge is largely done, just need to sort out some final decor.

Anyway, this year I plan to be a little less specific with my plans/resolutions, and try to do stuff more rather than achieve certain goals. I think this will work better for me.

Books

I love reading, particularly non-fiction, but I have a terrible habit of starting books and never finishing them. At present my bedside table consists of 8 unfinished books with bookmarks at varying depths throughout them. I also have 13 brand spanking new books that have yet to be opened, some from Christmas, but many from at least a year ago. So I intend to try and finish a book every fortnight or so. I’m not going to be strict as I still want to enjoy them, but an ongoing target should help keep the idea in mind.

Projects

As you’ll see from previous posts I also have a horrible habit of starting projects and never finishing them. I tend to procrastinate a lot with them and swap between them every few minutes or hours in my spare time, so nothing ever really gets done. So this year I intend to allocate a day a fortnight to just working on something I’ve been wanting to, and trying to only work on that one thing for that particular day. However, I don’t really count the seemingly endless DIY and decorating in this time, so this might be quite a tricky one to do, but the intention should at least yield some productive days.

So that’s my sort of resolutions for this year.

Advertisements

Making a Ball Mill – Part 2

Well it’s been a long time since I last mentioned my ball mill. I had a rather unsuccessful first try, and got a bit annoyed with it so didn’t even post anything about it. I’m now well into Ball Mill v2 and so thought I’d update on where I’ve got to. The motor and power supply I posted about earlier are still fine and will be using in my new mill, it’s just the mill itself that has cause some problems.

My first attempt was constructed of a wooden base with two upright panels. I mounted four ball bearing rings into holes in these uprights, with two hollow aluminium tubes running through them as my rollers. One of these was flush with the bearing at both ends, while the other protruded from the other side of the wooden panel, and would be used as the drive shaft.

I really should have planned it a little better but I was being too keen and building it on the fly. Firstly it was very difficult getting the bearings perfectly flush with the wooden upright, which is necessary to get a smooth rotation of the shafts. In the end they proved hard to turn by hand, so the motor was going to have a really hard time. In fact the wooden uprights rocked back and fourth by a millimeter or so as you turned the rollers, showing that everything was far from perfectly aligned.

Next problem was how to drive the rollers, and getting the right speed. I had initially planned to use a belt drive from the motor to the roller, but this proved too difficult without access to any proper bits for this. I tried using a hoover belt, but there was no grip without a proper slotted shaft of the motor and roller. Also speed was an issue, the motor has an internal gearbox which gives a nominal at 180rpm, and I need to spin my ball mill container at about 60-70rpm. Taking into account the roller shaft diameter and the diameter of the container it was going to spin way too slow. Again, I hadn’t really planned this in advance until it was built!

Ball Mill v2So a few weeks back I started on version 2, with a bit more planning this time. The first change was to make it all from metal to make it more sturdy, hopefully have higher precision, and also look a lot cooler too! I started by calculating the diameter of rollers I would need to get the optimal rotation speed, which handily was pretty much exactly 1″, plus 2.5mm that will be some kind of rubber on the rollers or container to give it good grip. I got hold of some solid aluminium bar for this, but into two pieces, and the very handy Stuart Hammond turned down the ends for me and centre drilled one of them for the motor shaft to be connected directly to.

Next was the bearings, this time I wanted them to have some flexibility so that they could align themselves to the rotation of the rollers, even if they weren’t perfectly in line. After looking through lots of options, I settled on some from Simply Bearings which came in adjustable pillow blocks, so the exact positioning had some movement until they were finally bolted down.

I decided to bolt the motor directly to a base place, with some angle aluminium to give it a sort of face plate for better stability. I figured that this would giver better stability for the motor. The base plate is a 250mm x 500mm x 4mm aluminium plate (also ordered online). I also got some aluminium flat bar of two specific thicknesses that are used as packing plates to bring the centres of the bearings up to the same height of the motor shaft, to try and keep everything on the level.

After accumulating all the pieces of the last few weeks I finally got round to drilling and assembling it all today, with the help of my Dad’s pillar drill and various other bits and pieces. The drilling proved a bit of a nightmare because of the size of the base plate, I couldn’t drill the centre of it as the drill couldn’t reach, so I had to do that one by hand with a power drill. It was incredibly fiddly drilling some the others too, as I drilled the packing bars and base plate at the same time, all clamped together, to give perfectly aligned bolt holes.

Only one small problem, I measured something slightly out, and the motor spindle doesn’t line up with the bearing opposite it! Oops, this means I can’t yet add the main drive shaft until I remove and reposition the motor. I’ll have to turn the bolt holes into longer slots so that the motor can ne moved a few millimeters. This might actually prove beneficial so that I have some adjustment to get the best alignment.

Projects for the year

I’m constantly thinking up ideas for projects I’d like to do but never seem to find any time for them. Or when I do I can’t decide which of them to tinker with so I end up spending flitting between them and achieving nothing. I’m determined to tackle some of the bigger ones this year, as this is the stuff that I truly enjoy. So I thought I’d write a list of them here, so I at least have a sort of To Do list of projects that might help me focus on them a bit more.

Pyro Fountain Tools

DONE. Ok, this one is here just so I know I’ve crossed off at least one! You can find out about these in previous posts on this blog.

26 Degrees of Separation

A photogrpahy experiment that I’ve been meaning to do for a very long time now. It involves taking a picture with a disposable camera then giving it to a friend to do the same, and then they pass it on to someone else and so on. The idea is that hopefully if one of the cameras ever manages to reach person 27 in the chain they will send it back to me. Once developed I should then have a set of 27 photos, starting with me and ending with someone 26 inter-personal connections away from me. These will all be published on the website 26degrees.org

This one has been on my list so long that I think  the cameras I bought for it are probably out of date by now and I’ll have to get some more! I really want to do this soon as it could take a long time for any of the cameras to make it back to me, if they ever do that is.

Near-Space Photography

Arduino GPS Tracker

Arduino GPS Tracker

This is something I’ve been thinking about for a couple of years now after reading about it in the fantastically inspirational, and snappily titled, book “Makers: All Kinds of People Making Amazing Things In Their Backyard, Basement or Garage“. It featured details of two amateur aerospace fans who launched a weather balloon into near-space with a digital camera on board that captured some beautiful images showing the curvature of the earth. What was more impressive was the low budget they had managed to do it on (~$500).

This really captured my imagination and I’m now on a mission to launch my own in a similar style. The real bonus here is that it covers so many of my interests as it involves science, electronics, photography, tracking and programming. I’m making some progress on this already; I’ve been busy playing with a GPS tracking using my Arduino microcontroller and a separate GPS unit, and I’ve just ordered two suitable weather balloons from a company in Belgium. There will be a LOT of work to do for this if it has any chance of success, but the aim is to launch in late summer/autumn of this year.

I’ll write more detail on this one soon.

Social Media iPhone App

Like all good ideas this one came from a lunch time chat down the pub! Me and my mate Jay came up with an idea for a social media name checking service, and decided to build it into an iPhone app, seeing as that is the latest craze!  I will be building the API and other server-side code while Jay builds the iPhone app interface. Still in early stages, but keep an eye out for the launch of uniqapp.com.

Ball Mill

Yes this is still on my list. I made a good start on this last year with building a 12v power supply, but I then made a prototype ball mill which was far from functional! I didn’t even get round to putting any details on here, although I might do later. I need to rethink my design and make it much simpler. I’ve been looking around on the UKPS forums at other users’ home-made mills and will be taking some inspiration from them. I’m keen to get this one done as it’ll mean I can start some proper experimentation with my own black powder for simple fireworks.

Making a Ball Mill – Part 1

Now that I’ve got all the ingredients and bits together to start making some black powder samples, I’ll need a ball mill if I want to make decent BP. The idea of the ball mill is that it grinds the chemical powders down until they are incredibly fine which allows them to mix together much better giving a much faster burn rate than in their raw state.

The principle is simple, you have a cylindrical container which is part filled with heavy lead balls (other balls could be used as long as they are also a non-sparking material). You put your powdered chemicals into the container along with the balls, and the while on its side the container is rotated, usually by the container resting between two rollers one of which is powered by a motor. This keeps the balls moving and colliding with each other, which pulverises the chemicals.

Now, I’ve not used one of these before so I will be experimenting to find the best speed of rotation, and also how long you need to mill for to get the best results. From all the reading I’ve done you are looking at a few hours milling time to get the best results.

I purchased a geared 180rpm 12v motor from eBay, which should give high torque and have no problem rotating the container (which will be quite heavy). I will probably use a belt drive from the motor to a pulley on the end of one of the rollers. This will allow me to reduce the speed further by adjusting the pulley size, to find the optimal speed.

I also purchased s heavy duty plastic container and some lead balls. My container is relatively small (about 17cm tall by 9cm diameter), but should do the job for small quantities. My lead balls are 17mm diameter and I have 50, which takes up about a third of the container. Ideally i think I should have more than this to fill it about half way, but we’ll see how I get on.

First job now was to find a way of providing a consistent 12v DC supply to the motor. It just so happens that this same week Matt, a guy I work with, had converted an old PC power supply to a lab power supply unit, which takes advantage of the existing 3.3, 5 and 12v supplies generated. Inspired by this, I decided to harness the 12v supply from a PC PSU as my power supply, which would not only be reliable but also came in a handy enclosure. Unfortunately I didn’t see Matt’s article about it until afterwards, but I had found this useful website article which detailed the PSU circuit basics.

After ripping the PSU from an old PC in my loft, I realised it didn’t have a power switch, which would be required to easily start and stop the ball mill. So I set about adding one that I had lying around. It fitted perfectly in the hole where all the old power cables came out of, and as I would only now need a single pair of cables coming out, I mounted in there with an improvised plastic plate and some screws. Following the wiring details from the article mentioned, I removed all but the cables I would need, soldered in a link on the circuit board that ensured the power remained on after pressing the power button, and generally cannibalised the innards.

I took an old cable exit grommet/sleeve from a pair of defunct hair clippers and attached this to the PSU, so that the 12v power cables could exit the unit through one of the air grilles without chaffing of damaging them. Then I rewired one of the male and female power supply connectors from inside the PC, so that the motor could be attached and detached from the PSU at will. This means I may be able to use the same PSU in fitire for other projects that require a similar supply (maybe a star roller next!).

After putting it all back together it looks not too shabby and works like a dream, plus the new power switch has a built in LED which adds a nice little touch!

The next step will be to build the rollers and pulley system to actually do the work, so I’m just trying to get my hands on some roller bearings and suitable materials.

View full photo set on Flickr